Jayess & Co. — Faridabad, India

An industrial identity built around engineering work

A proprietorship trading from Faridabad since 1990, building the electrical assemblies it also designs, tests, installs and energises.

Trading since: 1990
Works: Faridabad, Haryana
Quality system: ISO 9001:2015

Who we are

Jayess & Co. winds, assembles and tests distribution transformers, control transformers, servo voltage stabilisers and control panels at Faridabad. The work is done in one place: coils wound in-house, sheet fabricated and assembled, wiring ferruled to the schematic, and testing done before anything leaves the works.

What follows from that is the reason this site reads the way it does. A manufacturer who commissions its own equipment cannot afford a specification that was optimistic on paper, so nothing on these pages is stated without a document behind it.

Trading since 1990 — more than three decades of continuous operation. Udyog Aadhaar HR03B0008672, date of commencement 04/10/1990; independently restated on catalogue page 3
Manufacturing is in-house: design, winding, fabrication, assembly and testing happen under one roof rather than being bought in and badged. Catalogue page 3, "with all in-house manufacturing facilities"; consistent with the works testing station record
The company that builds the equipment is licensed to energise it — installation and commissioning are carried out under an electrical contractor licence issued by the Labour Department, Government of NCT of Delhi. Electrical contractor licence 50590000009690; Class 1 supervisor certificate

Front elevation of a multi-section low-tension panel lineup, doors closed. Two incomer sections on the left carry indication lamps, meters and rotary switch handles above glazed breaker windows; the sections to the right are columns of outgoing feeder compartments, each with a meter and a rotary switch-disconnector handle, with louvred busbar chambers along the top. — Main LT panel lineup at the works, doors closed. The two glazed windows on the left are the incomer breakers; every compartment to the right is an outgoing feeder with its own meter and switch-disconnectorMAIN LT PANEL — read from the designation label, not a range

Building highly engineered electrical assemblies for transmitting electricity, smartly automated and designed for industry.

What we set out to do — Catalogue page 4, stated mission (spelling of "highly" corrected from the source)

What we engineer

Four lines of work, and they are deliberately connected rather than separate departments.

Electrical consultancy and design for high- and low-tension systems.
Manufacture of transformers, stabilisers and control panels.
Industrial automation — PLC, VFD and motor control built into the panel that runs the plant.
Turnkey projects, taken from design through installation and commissioning.

What we manufacture

Each family has its own page carrying the specification, what is held on record and what is set per order. Nothing is summarised here that is stated more precisely there.

How the work runs

Five steps, in the order they happen. This is the company’s own account of its process — what makes it checkable is that the testing step has a works record behind it.

Design and specification — rating, schematic, configuration and application are defined. Company Profile 2026, page 4, step 01
Winding and fabrication — coil winding and panel fabrication are carried out in-house. Company Profile 2026, page 4, step 02
Assembly — core and coil, tank, busbar, control wiring and enclosure work are assembled to the design. Company Profile 2026, page 4, step 03
Inspection and testing — works checks are performed before dispatch, with documentation against the requirement. Company Profile 2026, page 4, step 04; the works testing station is a held evidence record
Dispatch and commissioning — equipment is prepared for site installation, testing and commissioning where that is in scope. Company Profile 2026, page 4, step 05; carried out under the Delhi electrical contractor licence

Where it is used

The applications the portfolio is built for. This is a list of sectors served, not a list of clients — no customer is named anywhere on this site without written permission.

Manufacturing
Infrastructure
Commercial buildings
Data centres
Healthcare
Utilities
EPC projects
Government projects
Industrial automation

What consultancy covers

Stated scope of the HT and LT consultancy, design and automation service. Which of these a project needs is settled at enquiry, not assumed.

Electrical system design
Electrical load analysis
Power quality analysis
Energy efficiency analysis
Code compliance
Safety inspections
Renewable energy integration
Cost estimation
Project management
Emergency response planning
Training and workshops

Equipment worked on

The HT and LT apparatus this consultancy and installation work covers, as stated.

HT and LT transformers
HT and LT circuit breakers
HT and LT isolators
HT and LT lightning arresters
HT and LT insulators
HT and LT distribution panels
HT and LT protection and control devices

Quality and evidence

Every certificate below is held on file and can be produced. Where a document says less than it appears to, the record says so — that is the point of publishing the limitation alongside the reference.

ISO 9001:2015 quality management certificateE20250830652Royal Assessments Pvt. Ltd., accredited through EGACOpen document
Electrical contractor licence — Government of NCT of Delhi50590000009690Labour Department, Government of NCT of DelhiOpen document
Licence requires all installation work to be carried out under the direct supervision of a holder of a Certificate of Competency Class-I (Electrical Supervisor), and by a holder of Class-II (Electrician)50590000009690Labour Department, Government of NCT of DelhiOpen document
Power control centres built to IS/IEC 61439-2IS/IEC 61439-2Referenced standard
Electrical testing station at the works, including a 5 kV high-voltage breakdown testerHVTD-5Evidences that the equipment exists and is in use. No calibration certificate, test report or type test is held, and none is implied.
Udyog Aadhaar (MSME) registration — Ministry of Micro, Small & Medium EnterprisesHR03B0008672Ministry of Micro, Small and Medium Enterprises, Government of India
Trading since 4 October 1990HR03B0008672Ministry of Micro, Small and Medium Enterprises, Government of India
Company Profile 2026, approved editionCompany Profile 2026Jayess & Co.Open document

Jayess & Co. — Company Profile 2026 Engineering capability, manufacturing approach, product portfolio and quality documentation in one document. The approved 2026 edition.

Download PDF 5022 KBNo form required
ISO 9001:2015 quality management certificate Certificate E20250830652, issued by Royal Assessments Pvt. Ltd. of Noida (QMS certification CAB# 119012) and accredited through EGAC, Egypt, a member of the International Accreditation Forum and signatory of its MLA. Certified 14 August 2025. The certificate runs to 13 August 2028 and states that validity is subject to successful completion of surveillance audits, due on or before 13 August 2026 and 13 August 2027; we hold no surveillance confirmation on file, so the later date is the certificate's term rather than a confirmed status. Names the Faridabad works at Plot 366, Sector 24, NIT and lists thirteen certified activities. Independently verifiable at iafcertsearch.org.

Download PDF 494 KBNo form required

At the works

Photographs of the plant and of equipment built in it. Click any frame to see it full screen.

A wide view along a multi-section LT panel lineup in the works shed, the full run of compartments receding to the right, with yellow busbar chamber labels along the top edge and a second lineup part-built against the wall behind. — The full run of the lineup, busbar chambers labelled along the top. Compartments are built out as separate verticals and bolted togetherBUS BAR — read from the designation label, not a range

A servo voltage stabiliser part-assembled in its steel frame: strip-wound buck-boost coils on a laminated core above, variable winding assemblies below, joined by aluminium busbar links to an insulated terminal board at the base. — Servo voltage stabiliser under assembly at the works — buck-boost winding above, variable winding assembly below

A grey testing console with four instrument panels, energised indication lamps, digital voltmeters and ammeters, four variac control knobs along the bench, and a high-voltage test lead coiled on the surface. — Electrical testing station at the works. The console carries a 5 kV high-voltage breakdown tester and four variacs labelled for transformer testingHigh Voltage Breakdown Tester 5 kV, model HVTD-5 — read from the nameplate, not a range

What is not published

Headcount and works area — no record has been supplied, so no figure is stated.
Client names, project references and testimonials — none is published without written permission and a verifiable project record.
Type-test reports, Form designations and short-circuit withstand ratings — not on file.
Turnover, capacity and production volumes — not published.

This list exists because its absence is the more common practice. A company page with round numbers and no sources is easy to write; a reader specifying equipment cannot check any of it.

Registered detail

Registered address: Plot No. 366, Sector 24, Industrial Area NIT, Faridabad 121005, Haryana, India
Works: Faridabad, Haryana, India
Trading since: 1990
Udyog Aadhaar (MSME): HR03B0008672
ISO 9001:2015 certificate: E20250830652
Electrical contractor licence: 50590000009690

Visit the works

If you are specifying equipment, standing in front of the plant answers more questions than a page can. Ask for a visit.

Enquiry WhatsApp — a quick technical question Jarnail Singh +91 98115 86006 Gursharan Singh +91 99103 84879 enquiries@jayessco.com — drawings and specifications